Page 1 of 1

A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 5:27 pm
by southparkkids
Well I found a couple of of upgrades for my A&K SVD at Airsoftpro.cz and was thinking on getting the Precision HopUp Chamber. Then I started looking at other parts I could upgrade and saw the CO2 upgrade set, the only thing is that between 600-700 fps might be too much (wouldn't be allowed because it was too high)?

Re: A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 5:29 pm
by TokenTech89
600-700 with what gram bbs?

Re: A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 5:53 pm
by southparkkids

Re: A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 10:08 pm
by specter
definitely .12's lol. they usually chrono with 12's to increase the "wow" factor

Re: A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 10:09 pm
by Star_folder
The video shows it being chronoed with .20g bbs.

Re: A&K SVD Upgrades?

Posted: Mon Jan 28, 2013 10:20 pm
by southparkkids
Ok, I just won't worry about that unless I get lots of money.

Re: A&K SVD Upgrades?

Posted: Tue Jan 29, 2013 2:45 pm
by fallout11
Assuming the A&K SVD is pretty much the same as the AtoZ /King Arms straight cocking spring SVD's, you don't need a new hopup chamber anyway, just a better bucking (I liked the promy purple) and different nubbin (carved my own).
There's lots you can do with/to these (used to own the AtoZ one), but honestly not much that is really needed. Biggest improvement is in securing the buttstock to the receiver better, using 4 bolts rather than 2....see me at an event and I'll show you what I mean (as its been many years now and it is easier to explain with one to look at).

Re: A&K SVD Upgrades?

Posted: Tue Jan 29, 2013 2:48 pm
by Star_folder
I don't believe the A&K SVD is the same design as the AtoZ SVD. The hop up adjust throught the magwell with a hex head, which is quite a pain.

Re: A&K SVD Upgrades?

Posted: Tue Feb 19, 2013 11:25 pm
by southparkkids
Finally got new hop-up in today and installed it. It works great but took about 20 days to get here, customs you know.

Re: A&K SVD Upgrades?

Posted: Wed Feb 20, 2013 12:39 pm
by marpat96
The SVD piston and various upgrades in that department are now for sale in stores, just look them up. I know ASGI has them in stock.

Re: A&K SVD Upgrades?

Posted: Sun Mar 03, 2013 9:42 am
by fallout11
The AtoZ also has a hex head grub screw to adjust the hopup, only it is under the upper receiver cover rather than in the magwell (actually harder to use).

Re: A&K SVD Upgrades?

Posted: Sun Mar 03, 2013 1:13 pm
by southparkkids
What hop-up bucking would you suggest? I'm also going to get a inner barrel eventually so any thoughts on what the best inner barrel would be for this?

Re: A&K SVD Upgrades?

Posted: Sun Mar 03, 2013 1:52 pm
by fallout11
The AtoZ came with a systema 6.04 brass tightbore, which I discovered AFTER spending money and replacing it with a Promethius 6.03 stainless tightbore. Dumb on my part.
If this was 2008 I'd recommend a Promy purple bucking (plus quality .30g or heavier BBs and the power up 500 fps spring....the AtoZ model took a special longer-than-AEG-length spring), but no doubt lots has changed since 2008 that I simply haven't kept up with, so take that with a grain of salt.

I also modified the way the stock mounts on the gun to stabilize it better (4 screws rather than 2), changed the O-ring on the piston, and put an O-ring (could use sorbo pat) in the bottom of the cylinder head. Again, YMMV.