AGM MK96 spacer

I broke my gun!
Post Reply
Hotspur93
I love forums!
I love forums!
Posts: 339
Joined: Wed Nov 17, 2010 4:45 pm
Location: Columbia, SC

AGM MK96 spacer

Post by Hotspur93 » Sun Jan 23, 2011 4:30 pm

Hey all so i recently got a an AGM MK96. Well to start off is shoots great! However the spacer inside the barrel slides around T.T from this it means that the barrel is always in a different position depending on where the spacer is in the barrel. So anyone have any tips to get it back in one spot so it will stop curriving in random directions at random times?
Veteran of:
OP: Second Sun OP: Iron Marches
OP: Phantom Hawk
OP: Phantom Hawk II
OP: Blackwater
TDC
SGC
OP: Vietnam Patrol
OP: Decisive Force

Dominum
Global Moderator
Global Moderator
Posts: 6421
Joined: Mon Sep 28, 2009 10:14 am
Location: Swansea, SC

Re: AGM MK96 spacer

Post by Dominum » Sun Jan 23, 2011 4:47 pm

Add teflon tape around the spacer(s) to make it a tight fit inside the outer barrel.
PRincess and jsts ghost CERTIFIED "Tier 1 Operator"
[align=center]Image[/align]
[align=center]"Searching for my goats since 2009"
"All you have done here is take the typical leftist line and regurgitate it in a barely palatable,
quasi poetic, pseudo intellectual format. Quite frankly, that makes you a moron."[/align]
  ▲
▲ ▲
[align=center]V[/align]

Hotspur93
I love forums!
I love forums!
Posts: 339
Joined: Wed Nov 17, 2010 4:45 pm
Location: Columbia, SC

Re: AGM MK96 spacer

Post by Hotspur93 » Sun Jan 23, 2011 5:18 pm

Alright any suggestions for getting the spacer out of the barrel past the threading?
Veteran of:
OP: Second Sun OP: Iron Marches
OP: Phantom Hawk
OP: Phantom Hawk II
OP: Blackwater
TDC
SGC
OP: Vietnam Patrol
OP: Decisive Force

Smoke
AJAXian
AJAXian
Posts: 159
Joined: Sun Jul 25, 2010 9:26 pm
Location: spartanburg

Re: AGM MK96 spacer

Post by Smoke » Sun Jan 23, 2011 5:56 pm

Pm me your phone number and help you through it..... Im not 100 percent sure on this rifle but i would think there should be a set screw that holds the hop up unit and inner barrel in place and it should screw in through the outer barrel and into the hop up?  ( very small screw)  like i said though im not 100 percent on that but if i didnt have one i would add it if it were my rifle
tm l96 aws
kwa sr-12
kwa sr-5
echo 1 asr
de m81
kwa g17

Hotspur93
I love forums!
I love forums!
Posts: 339
Joined: Wed Nov 17, 2010 4:45 pm
Location: Columbia, SC

Re: AGM MK96 spacer

Post by Hotspur93 » Sun Jan 23, 2011 6:55 pm

Hey sorry i figured it out already 8). Yeah after going through the end of the barrel didnt work i decided that i would take the gun apart slowly and see what i could do. And like u said several tiny screws later i was able to take the inner barrel and the hop up unit out as one piece for the outer barrel. From there it was easy to fix the spacer, then i just put it all back together. But thanks for the offer and also thanks for the advice!
Veteran of:
OP: Second Sun OP: Iron Marches
OP: Phantom Hawk
OP: Phantom Hawk II
OP: Blackwater
TDC
SGC
OP: Vietnam Patrol
OP: Decisive Force

Post Reply