Latest Acquisition

[Straightshot]

Looks pretty sweet SteevoLS

[Doublewolf]

That's some nice stuff Vesper.
Also, nice holster severed.

---

SteevoLS, that has got to be one of the coolest airsoft guns I have ever seen. I love the mags, and the stock and foregrip look nice too. I can't wait to see it when it's finished. The Magpul UBR stock is going to look awsome.

---

[SteevoLS]

The PMAGs are great; very sturdy, well made, and visually attractive. That said, they are intended for the A&K Masada and the ONLY line of Armalites I know of that will fit them well is the VFC M4s, M16s, and 416s.

[Bushmaster]

That is technically my CTR stock, that being said though, nice stuff all!

[Dominum]

Latest acquisitions .
[img width=700 height=468]http://i284.photobucket.com/albums/ll8/ ... 2613-1.jpg[/img]
This is my new DMR. It's based on an E1 G3 SG1, and yes, I plan to get a nicer upper and lower receiver and outer barrel assembly in the near future. It should be shooting at about 520FPS, I use KSC .30s or Maruzen grandmaster .29s in it, but I'd like to try some heavier Madbulls to see if they perform even better. If anyone has .36s or heavier I'd like to buy a couple hundred to test out please. I fielded it at TT and was very happy. Instant trigger response, awesome range and accuracy. It looks good (IMHO) and handles well, light and comfortable. My only complaint is that the plastic body can bend a bit at the joint between the upper receiver and outer barrel assembly, but that will be fixed with new ones. I decided to use my stubby Zombie Killer suppressor for TT, but I may use my SOCOM style in the future. Both are functional, but I think it will need some sorbothane (more, that is, as it likely has it already) and some additional mods to be more quiet. Here's the part list:

Outside:
-High profile RIS mount, I forgot who made it, but it's solid and fits well, with a side mount I may find a use for
-4X40 illuminated R/G MilDot scope with external windage (The one that was in my FS thread)
-Low profile 1" rings
-Condor 3 point sling, switches to a 2 point when needed, and came with a bunch of extras I don't know what to do with LOL
-Not sure which I'll use yet, but either the TM SOCOM suppressor with foam, or the Stubby Zombie Killer suppressor with foam
-5 King Arms 110rnd MidCaps

Inside:
-Prometheus 470mm 6.03mm stainless steel tightbore barrel
-Firefly hard type AEG bucking
-Firefly hard type AEG nub
-TM EG1000 motor, may replace with a Systema, but I haven't made up my mind because the TM is so quiet and still pulls it well
-2200mah 11.1v 15C LiPo
-Systema drop in M150 gearbox for G3SG1 *I haven't had the chance to open it, but I was happy that it came with a MOSFET installed, with active breaking I presume and a helical gearset. When I open it for a tune up this weekend I will complete the gearbox parts list in detail.




...Need I say more?


I also bought a Condor crossover leg rig, fold away dump pouch, and quick release holster. They are great, and I have finally found gear that I like and isn't stuffy and cumbersome like a PC or LBV.

*Updates: I was very happy with the Systema drop in; all ball bearings, helical gears, MosFet, BO teflon cylinder, silent heads, etc. A flawless setup for an M150 IMO, Systema did an excellent job with their drop in M150s.

Also, I recently acquired a TM G3 SG1 body for it, plus some hicaps and lowcaps, and I'll be getting even more mags. I also built a fully upgraded high speed 400 FPS gearbox for it, as well as a fully upgraded very high speed 340 FPS gearbox for it. The only thing I still need is a short front end for the CQBR setup.

[Dominum]

Wow Stephen, that is NICE! I can't wait to see it in about an hour...

[Esteban]

Have you tried the G3 out with 0.36g's yet?

[Vanquish]

I finally got my MOE handguards.  I've been wanting to get these bad boys for a long time. 

I'm reconfiguring my KWA again too.  I think this is the 4th time now that I've done that. lol

[img width=600 height=450]http://i12.photobucket.com/albums/a202/ ... G_0701.jpg[/img]

[Bushmaster]

Ah, I think you shall like them, I can't wait to get mine onto my M4, wish I didn't have to wait 'til the 20th...

[Esteban]

I finally got my MOE handguards.  I've been wanting to get these bad boys for a long time. 

I'm reconfiguring my KWA again too.  I think this is the 4th time now that I've done that. lol

What are your plans?

[Vanquish]

What are your plans?

I found a CQB outer barrel in my stash of parts, so that's going on there now along with the new handguards.  The inner barrel will be the same length as before, but now the barrel will run up through the suppressor a few inches.  I knocked about 4 inches off the total length of the gun which is nice.

[Bushmaster]

I found a CQB outer barrel in my stash of parts, so that's going on there now along with the new handguards.  The inner barrel will be the same length as before, but now the barrel will run up through the suppressor a few inches. 

Can anyone say "Awesome"?

[Dominum]

Have you tried the G3 out with 0.36g's yet?

Not yet, but I plan to try either .36s or .40s. I've run the Madbull .40s in other high FPS setups of mine and I liked their performance, so we'll see. As of the moment I am running KSC .30s and Maruzen Grandmaster .29s.

[Doublewolf]

My new G&G Combat Machine M16 Carbine.

[img width=700 height=525]http://i419.photobucket.com/albums/pp27 ... 0002-1.jpg[/img]
[img width=700 height=525]http://i419.photobucket.com/albums/pp27 ... CT0005.jpg[/img]

Was supposed to have USMC trades, but just before I bought it, the USMC made G&G stop putting it on there.  It's still a great gun though.

All stock. I put a sling and UTG bipod on it.

[Red Fury]

nice i like the m4 DW