Putting a full stock on my KWA sr10

I broke my gun!
Post Reply
silverwolf
F.N.G.
F.N.G.
Posts: 17
Joined: Thu Feb 25, 2010 5:49 pm

Putting a full stock on my KWA sr10

Post by silverwolf » Sun May 01, 2011 4:51 pm

Ok, I am going to put on a full stock onto my kwa sr10 but i have run into a problem. I got the crane stock off but the wiring was still attached and i could not find out where to disconnect them from the gun. Any ideas?
Top
Dominum
Global Moderator
Global Moderator
Posts: 6421
Joined: Mon Sep 28, 2009 10:14 am
Location: Swansea, SC

Re: Putting a full stock on my KWA sr10

Post by Dominum » Sun May 01, 2011 5:08 pm

If it does not have an extension with a small tamiya plug then you will either have to feed it through as is or solder on your own. If you do, avoid tamiyas.
PRincess and jsts ghost CERTIFIED "Tier 1 Operator"
[align=center]Image[/align]
[align=center]"Searching for my goats since 2009"
"All you have done here is take the typical leftist line and regurgitate it in a barely palatable,
quasi poetic, pseudo intellectual format. Quite frankly, that makes you a moron."[/align]
  ▲
▲ ▲
[align=center]V[/align]
Top
silverwolf
F.N.G.
F.N.G.
Posts: 17
Joined: Thu Feb 25, 2010 5:49 pm

Re: Putting a full stock on my KWA sr10

Post by silverwolf » Sun May 01, 2011 7:06 pm

there is some casing around part of the wire where it looks like it connects it to the gear box but i dont know id i should take off the casing and put on the new wires and put elctrical tape around it. (i don't know if they are the right connectors)
Top
Dominum
Global Moderator
Global Moderator
Posts: 6421
Joined: Mon Sep 28, 2009 10:14 am
Location: Swansea, SC

Re: Putting a full stock on my KWA sr10

Post by Dominum » Sun May 01, 2011 8:38 pm

What do you mean by casing? Pics please.
PRincess and jsts ghost CERTIFIED "Tier 1 Operator"
[align=center]Image[/align]
[align=center]"Searching for my goats since 2009"
"All you have done here is take the typical leftist line and regurgitate it in a barely palatable,
quasi poetic, pseudo intellectual format. Quite frankly, that makes you a moron."[/align]
  ▲
▲ ▲
[align=center]V[/align]
Top
User avatar
SteevoLS
Admin
Admin
Posts: 5323
Joined: Mon Sep 28, 2009 8:16 am

Re: Putting a full stock on my KWA sr10

Post by SteevoLS » Sun May 01, 2011 8:54 pm

I was just working on one of these a few minutes ago. Just unscrew the fuse from the rear of the crane stock and it should slide back through the buffer tube.
Image
There's no kill switch on awesome!
Top
silverwolf
F.N.G.
F.N.G.
Posts: 17
Joined: Thu Feb 25, 2010 5:49 pm

Re: Putting a full stock on my KWA sr10

Post by silverwolf » Mon May 02, 2011 6:40 am

Their are some connectors wrapped in plastic but I don't know if I should touch it. And every time I try to post pics it does not allow it.
And Steevols ill try that
Top
Felix
AJAXian
AJAXian
Posts: 2786
Joined: Fri Jul 16, 2010 11:25 am

Re: Putting a full stock on my KWA sr10

Post by Felix » Mon May 02, 2011 7:27 am

post to photobucket then post the image link here
Top
Post Reply

Return to “Technical Topics”